-
LOCATION:HOME >> NEWS >> Industry news
-
Industry news
A Bus Shelter Fails at the Kerb, Not in the Sky
The smallest building a town buys in batches
A bus shelter is a roof with somewhere to sit, and almost nothing else. It has no walls worth the name, no heating, and no foundation deeper than a hand. The ST02Z galvanized steel sheet page names the product honestly in its application list, between stations, yards and airports, which tells you the shelter belongs to the same steel family as a station canopy. What the application list does not tell you is that the shelter is the hardest duty in that family: a station canopy is part of a building, while a shelter stands alone at the kerb, taking the full wind on a small area and the winter salt a metre from the road.
Uplift, not weight, sizes the structure
Because a shelter roof is open underneath, the wind gets under it as well as over it, and the two pressures do not cancel. Take a gust of 33 metres per second, roughly 120 kilometres per hour, which a coastal or exposed site sees several times a decade. The velocity pressure is half of 1.25 times 33 squared, which is 680 pascals. A typical shelter roof covers 4.0 metres by 1.5, or 6 square metres. Apply a net uplift coefficient of only 1.0 to stay on the safe side of the gust arithmetic and the roof is pulled upward with a force of 680 times 6, about 4,080 newtons, which is 415 kilograms trying to leave.
Now weigh what holds it down. A 0.5 mm galvanized roof sheet runs to 3.9 kilograms per square metre, so 6 square metres of sheet is 24 kilograms. Add the frame, the back panel and the gutters and the whole shelter is perhaps 85 kilograms. The uplift is close to five times the dead weight. A shelter does not stand on its posts; it hangs from its anchors, and the anchor design is the structure.
Four posts and a bolt group
Spread over four posts, the uplift is around 100 kilograms per post before any gust factor. Each post is therefore a tension member, anchored into concrete, and the base plate is sized for pull-out, not just shear. This is why the post material is a pipe rather than a rolled section: a round tube has the same section in every wind direction and is easy to cap, drain and galvanize. The ASTM A53 carbon steel pipe page covers welded and hot-dipped galvanized pipe from a nominal bore of half an inch up to 36 inches, in wall gauges between 3 and 12 millimetres; even Grade B, at 60,000 psi tension and 35,000 psi yield, is more than a shelter post ever asks of it. The post is bought for its coating and its geometry, not its tensile rating.
The kerb is worse than the climate map
Corrosion at a bus stop is not a general atmospheric problem; it is a splash-zone problem. Every winter morning the first half-metre above the pavement gets a mist of de-icing salt from every vehicle that brakes at the stop, and the coating pages rank service life from rural, through industrial, up to general and then serious marine exposure. A salted kerb in an inland town behaves closer to the marine end of that ladder than the map suggests. The prepainted Galvalume corrugated roof page puts the aluminium-zinc coating at two to six times the life of plain galvanized sheet of the same thickness, and the outdoor parts of a shelter are exactly where that premium is earned.
Where plain zinc is chosen, the coating mass is the whole negotiation. The ST02Z galvanized coil and sheet pages run Z40 to Z275, and the Z275 galvanized steel coil page lists its zinc range as 30 to 275 grams per square metre on 0.12 to 2.0 mm steel in widths from 600 to 2,000 mm. At Z275 the total zinc works out near 19 microns on each face. At the top of the SGCC galvanized steel sheet range, 600 grams per square metre, the coating is around 42 microns a face, which is the number to specify for the ground metre of every post and the curb-side edge of every panel.
Profile, drainage and a place that stays cool
A flat 0.5 mm sheet will oil-can between purlins, so shelter roofs are profiled. The galvanized corrugated steel plate page spans 0.19 to 2 mm in widths to 2,500 mm and describes the sheet as suited to deep processing into corrugated profiles, and a shelter order is usually a slit-and-roll-form job exactly like that. The mono-pitch falls should drain to the pavement edge, and a shelter without a gutter dumps its 6 square metres of rainwater on the very people waiting under it. The SECCN2 galvanized steel sheet page lists rainwater gutter among its roll-formed applications, alongside curved profiles and metal doors; note that its 40, 60 and 80 gram electro-deposited coating belongs in dry interiors, not at a kerb, so the gutter is roll-formed from hot-dip coil even when the same shape is shown on an electro-galvanized page. The galvanized steel processing product catalogue exists for exactly these non-standard sections: gutters, edge flashings and bracket plates drawn from coil to a shelter-maker's drawing.
The roof also has a thermal job. The ST02Z coil page claims high heat reflectivity that keeps the surface from getting hot even in summer, lowering the temperature under the sheet by 6 to 8 degrees, and a waiting passenger can feel the difference between a bare reflective roof and a dark painted one. Where a town wants a colour, the TDC51D PPGI prepainted galvanized steel coil page offers RAL colours or a customer sample on 0.12 to 2 mm strip in widths to 1,250 mm, and a light shade keeps most of the reflectivity.
The parts people actually touch
The back panel is usually laminated glass in a galvanized frame, with a sheet-steel advert skin on the outside; the ST02Z application list ends with advertising and decorating, which is the honest description of what most shelter rear panels become. The bench is the only stainless in the order. It gets sat on, leant against and wiped daily, and its tube wants to be drawn from the square stainless steel pipe range, which runs from 10 x 10 mm square sections to rectangular 10 x 20 up to 120 x 180 mm, with grade 201 in the standard table. A bench of 40 x 80 rectangular tube costs little more than painted carbon steel and never needs the paint renewed.
What the order should say
Written as a steel list, a shelter is short: Z275-or-heavier hot-dip sheet at 0.5 mm, corrugated, for the roof; 600 gram coating or an aluminium-zinc substrate for the bottom metre; A53 Grade B pipe posts, capped and drained; a roll-formed gutter from processing coil; a 201 stainless bench; and anchor bolts chosen for a hundred kilograms of uplift per post rather than for gravity. The towns that skip the last line are the ones whose shelters are found in the road after the first proper gale.