-
LOCATION:HOME >> NEWS >> Industry news
-
Industry news
A Window Frame Is a Movement Joint With Glass In It
The opening moves; the frame has to allow it
A window is where a steel frame passes through a wall, and three materials meet with three amounts of movement. The frame expands with its own temperature, the glass moves far less, the wall barely moves. Sealant covers the joint but does not absorb the difference. A window that leaks or cracks a pane at the corner after two winters was usually fixed as though the opening were rigid.
One and a quarter millimetres on an ordinary frame
Take a frame 1.8 metres wide in a wall that swings from minus 10 to plus 30 degrees Celsius, a 40 kelvin range. The 304 stainless steel page gives a mean expansion coefficient of 17.2 millionths per kelvin, so the frame grows that figure times 1,800 millimetres times 40, or 1.24 millimetres. A carbon steel frame at roughly 12 millionths moves 0.86 millimetres. Both look small until the frame is welded in at both ends, and the movement goes into the glass, the weld or the plaster.
Glass has the least tolerance. Soda-lime glass expands at about 9 millionths per kelvin, so a 1.8 metre pane grows 0.65 millimetres across 40 kelvin while the frame around it grows 1.24. That difference is why a pane needs three to five millimetres of edge clearance and must never sit hard against steel on four sides. A three metre opening moves 2.06 millimetres, and the joint stops being theoretical.
The fixing is the joint
A frame bolted tight at every point has no joint, whatever the drawing says. The usual detail is one fixed point per frame, normally at the centre of the head, with the remaining fixings in slotted holes that let the frame slide. A 12 by 30 millimetre slot gives 18 millimetres of travel, far more than the 1.24 millimetres calculated above, and the screw holds without clamping the frame. Packers at roughly 600 millimetre centres keep the section straight; a frame pulled onto an uneven opening bows between fixings and twists the rebate.
The section has to be stiff enough not to sag between packers. The square stainless steel pipe range covers 10 x 10 mm to 100 x 100 mm in lengths to 12 metres, held to within 1 per cent, and a 40 x 40 mm section at 1.5 mm wall is a common mullion. In grade 201, listed at a transverse yield of 292 megapascals on the 201 stainless steel page, it carries a fixed light comfortably.
Condensation picks the coldest surface
In a room at 20 degrees Celsius, air at 50 per cent relative humidity condenses on any surface below 9.3 degrees. Any surface below that collects water, and a steel frame is the coldest surface in the room because it bridges directly to the outside. On a zero degree day the inner face can sit below the dew point even when the glass, with its trapped air space, stays clear. The water runs down the frame into the rebate.
That is why a steel window needs a drained and ventilated rebate rather than a sealed one. Weep holes of about 8 millimetres at the sill, two per pane, let the water out; a rebate sealed on the room side traps it against the gasket, where it reaches the setting blocks and the edge of the glass. A thermal break, or a warm-edge spacer in an insulated unit, moves the cold surface away from the room but does not remove the need for drainage. The galvanized processing product route exists for sills and trims rolled to the window maker's profile, and those parts need the same fall and outlet as the frame.
Coating a frame that gets cut and welded
A frame is fabricated after coating or coated after fabrication, and the choice decides where rust starts. On the pre-coated route it is roll-formed from Z275 galvanized coil, 275 grams per square metre, or about 19 micrometres per face, and the cut ends and weld seams are the only bare steel. On the fabricated route it is welded first and hot-dipped afterwards, and the SGCC galvanized sheet range runs from 30 to 600 grams per square metre, with 600 grams giving about 42 micrometres a face. Hot-dipping a thin welded frame at around 500 degrees distorts it, so straightening belongs in the price.
Where a colour is required, a TDC51D prepainted coil gives a factory finish on strip from 0.12 mm to 2 mm thick and up to 1,250 mm wide, and a powder coat over zinc gives a thicker film still. The cut edge remains the weak point, and a zinc-rich touch-up on every cut and weld is the cheapest durability measure on the window. Interior panels that do not need 304 can use 430 stainless coil strip, which has a lower expansion than the austenitic grades and moves less against a plaster reveal. Roll-formed frames price against 304 and 304L coil and the hot-dipped galvanized coil range.
Two metals in a wet rebate
The frame is usually galvanized steel and the fixings are usually stainless, which is a galvanic pair. Zinc is the anode, and the zinc area around a screw head is small against the stainless screw, so the coating is consumed locally and the rust ring appears around the fixing rather than in the middle of the frame. Zinc-flake coated screws, or a nylon washer under a stainless head, break the contact. The same rule covers hinges and handles: brass against zinc in a damp rebate fails in the first winter.
The glass needs a drained rebate, not a bed of sealant
Glass should bear on setting blocks at the quarter points, never on the frame, and the gasket should be EPDM rather than a painted steel edge. The rebate needs about 15 millimetres of edge cover, a fall to the outside, and a path to the weep holes that does not pass through the room-side seal. Where the frame is stainless, grade 201 is adequate inland, but the 316L stainless steel page is the one to quote for a coastal facade, and stainless steel pipe in the same grade makes a durable sill rail where the frame meets a public floor.
What the drawing and the order should carry
Put the movement on the drawing: one fixed point, slotted fixings elsewhere, a joint at each end of a long run. Put the drainage on it too: weep holes, a fall, a rebate open to the outside. The order needs the frame section and wall thickness, the alloy for the exposure, the coating mass rather than the coating name, and the glass bite. The A653 structural coil page is where to check that the sheet grade suits the forming operation, and the galvanized steel plate range covers the anchors and brackets that hold the frame back to the structure. A window is a small part of a building's steel, but it is the part the occupants touch, and the part that shows every mistake in the joint.
Next:No More!